🛠️ What have you done to your F150 Tremor this week?

[apetty]

did you go with under seat or behind the seat for your new sub?

I’m going with the behind the seat since it uses only the unusable space behind the seat.

 

[Cblaxx19]

I’m going with the behind the seat since it uses only the unusable space behind the seat.

looking forward to your review of it. i've been eyeing a behind the seat setup from MTI Acoustics. just havent pulled the trigger.

 

[NXPRSS]

This last week I added, Wheathertech mud flaps, Husky wheel well liners, short antenna, Xpel ppf on the front end, Undercover Ultra Flex tonneau cover, Rhino lining bed protector, and a F-150 decal on the tailgate. Also ordered sound treatment for the doors and a nice subwoofer to replace the stock B&O sub from Sounds Good Stereo.

Where did you order the f150 decal from??

 

[metallikatz3]

I had to cut the bed rug out to mount the slide and I have about an inch of room with the protective cover on. I have a CFX3 DZ75 with the matching Dometic slide. It raises the fridge about 1.25"-1.5" from the floor of the truck. It just fits and barely makes it past the tail gate with the work surface on it when it slides out.

View attachment 20533

How'd you secure the fridge slide down? I'm guessing a few rivnuts?

 

[apetty]

Where did you order the f150 decal from??

The decals came from LUDesignsNY on Etsy. They were very well made and came with super easy install instructions. There were tons of colors for background and the outside trim

 

[MikeJ19]

Received my RCI order and installed it within 90 minutes of arrival.
View attachment 14477

Hey Yeti…. Did you go aluminum or Steele on these? Been wanting to do this since I bought my Truck.

 

[Beachnuts]

Spray in bed liner, weather tech floor mats, & LED license plate lights. Black on black Raptor wheel caps ordered today.

 

[mAtTyG04]

I was going to remove the bedside decal completely but ended up going the opposite direction. I found the original decal too small for the truck so I scaled it to Raptor size. Tremor I like. 35 I have mixed feelings.

 

[Billd1966]

I was going to remove the bedside decal completely but ended up going the opposite direction. I found the original decal too small for the truck so I scaled it to Raptor size. Tremor I like. 35 I have mixed feelings.

View attachment 20692View attachment 20696

Looks good brother!

 

[NXPRSS]

The decals came from LUDesignsNY on Etsy. They were very well made and came with super easy install instructions. There were tons of colors for background and the outside trim

Cool, I just ordered from him. Matte black with tremor orange outline..

 

[FatSacs]

AM in the sunlight hits different

 

[toothofman]

Well I bought it 3 days ago (awesome) and I already get to replace the rear windshield (sub-awesome). I shot USPSA yesterday and a rock must have jumped over the 30ft berm and perfectly hit the edge of the rear slider. My luck with vehicles recently man.....

 

[Fozzy]

Used the crap out of it and was so impressed with it. Towed in 110 degree heat with no problems at all. Super surprised with the fuel milage being the same as my trucks that were leveled on 35's vs 6" and 37's. I was expecting the rack, lift and tires to totally kill the milage. Solar panels and bluetti kept up with the fridge for 4 days of heat without needing a recharge. Rack doesn't whistle or rattle, suspension soaked up the wash board roads so good I had to remember I was pulling the boat and slow down. Pulling the boat out on the pipe mats it didn't spin a tire one. And it would get a crowd everywhere it went. Truck totally hits the Show, Go and Tow I was looking for. So glad I didn't get the Raptor or a Superduty.

Gota pay to play

First trip back to Mead in a few years due to low water levels, didn't disappoint.

Mostly glass all weekend.

 

[FatSacs]

Installed the Tufskinz door sill protectors. Really wanted the V1’s but I still like.

 

[JTTremor]

Installed the Tufskinz door sill protectors. Really wanted the V1’s but I still like. View attachment 20837View attachment 20838

Nice, was the design yours?

 

[FatSacs]

Nice, was the design yours?

No it’s an available option. Was either blank, “F150”, or the mountain. Was t sure how I’d feel about it but I actually like it and think it’s fits the Tremor well

 

[FatSacs]

I’ll also drop one of the professional pics I had done

 

[JTTremor]

No it’s an available option. Was either blank, “F150”, or the mountain. Was t sure how I’d feel about it but I actually like it and think it’s fits the Tremor well. Nice choice, looks good.

 

[JTTremor]

No it’s an available option. Was either blank, “F150”, or the mountain. Was t sure how I’d feel about it but I actually like it and think it’s fits the Tremor well

Nice choice, looks good.

 

[Dieselquads]

Had Bilstein 5100's installed at all four corners then installed Belltech rear sway bar myself. Between these two mods, the truck handles so much better than any truck I've ever had before. I used the middle setting on the sway bar. These mods prevent the truck from leaning in corners and the secondary body motion after completing a turn. Much more planted and confidence inspiring without roughening the ride. This is how Fords should ride in my opinion instead of the stock sloppy floppy handing.